How to Safely Replace a Garage Door Spring in Barrie

Understanding Garage Door Springs

A garage door is one of the most heavily used appliances in a home, and like any other household item, it can eventually break. When it does, you’ll usually notice the problem comes from a damaged or broken spring. A garage door spring usually lasts for about 10,000 cycles or up to seven years before it snaps or gets damaged. If you notice that your garage door is making strange sounds or it isn’t opening or closing as smoothly as it used to, then it’s probably time to check the springs. Want to know more about the topic covered in Visit this helpful guide article? Garage Door Openers Barrie, filled with additional and valuable information to supplement your reading.

Types of Garage Door Springs

Garage doors are typically supported by two types of torsion springs: standard and high cycle. Standard springs are the most common, as they are cheaper and have a life expectancy of about 10,000 cycles. High cycle springs, on the other hand, are more expensive and can handle up to 50,000 cycles. If you have a high-traffic garage, investing in a high cycle spring is the better option in the long run. Be sure to determine the proper spring measurements and type before purchasing a replacement.

How to Safely Replace a Garage Door Spring in Barrie 3

Tools You’ll Need

  • 2×4 wood block
  • Adjustable wrench
  • Vice grips
  • Phillips screwdriver
  • Clamps
  • Torsion bars
  • Replacement garage door springs
  • Steps to Replace a Garage Door Spring

    It’s important to note that garage door springs are tightly wound and under a lot of pressure, so it’s more than advisable to call a professional if you are uncertain about your safety. Replacing a garage door spring can be dangerous, and it’s not a good idea to attempt it alone. However, if you’re confident enough to do it yourself, here are the steps:

  • Disengage the garage door opener
  • The opener should be unplugged and locked out by attaching a clamp to the opener connecting arm on top of the door.

  • Unwind old springs
  • Place the winding bar between the winding cone and the garage door’s header, then loosen the two set-screws. Use two winding bars to push the winding cone down while keeping it in place with the first winding bar. Repeat the process on the other spring.

  • Loosen bolts and remove springs
  • After thoroughly ensuring that the winding bar is in place, remove the bolts that secure the stationary end of the spring to the center bracket. Once the bolts are out, slide the spring towards the center bracket to relieve the tension on the screws holding the spring on. Rotate the spring off the rod and remove it.

  • Install New Springs
  • Attach the new spring onto the bracket using the nuts and bolts included in the package. Slide the torsion rod into the bracket and tighten it. Using the two winding bars, wind the new spring tightly into place, making sure it is solidly in place before you let go.

  • Wind new springs
  • Winding the the new springs is similar to unwinding the old ones. Use two winding bars and make sure the winding cone isn’t spinning freely prior to winding it. When the hub is secure, wind the new springs tightly, making sure each set screw is secure.

  • Test the garage door
  • Once you’re done with the spring installation, remove the vice grip from the track systems and plug in the garage door opener again. Test the door to ensure it’s opening and closing smoothly.


    Replacing a garage door spring isn’t an easy task, and it’s important to take all the necessary safety precautions. Before attempting to replace a garage door spring, ensure you have all the tools you need, and understand the process to ensure that the job is done correctly. It’s also important to determine the type and size of the replacement springs required to avoid any errors. Be sure to follow the steps outlined above, and if you’re unsure about anything, it’s best to call a trained technician to avoid any unwanted accidents. Want to keep exploring the subject? Garage Doors Barrie, we’ve selected Visit this helpful guide for your further reading.

    In case you have almost any questions with regards to where by and also the best way to utilize Visit this helpful guide, you possibly can contact us with the page.